Elevanfilm EDL-DT Series | Rotary Film Developing Tanks

Price range: $100.00 through $157.00

A thick-wall PVC film developing tank with a threaded closure, a gear-drive cog lid for a compatible JOBO Lift, and a sealing plug for hand processing. Choose 2520, 2530, or 2550.

Optional tank-base magnet: +$18. Select it with any model if you use a compatible magnetic-drive processor. Reels and processor not included. Prices exclude shipping.

SKU: EDL-DT Category: Brand:

Description

01 / Tank selection guide

Which tank fits your batches?

Pick for the batch you process most often, not the biggest batch you might ever run. These recommendations assume one 35mm roll per JOBO 2502 reel.

1–2 rolls · Small batches

2520

Pick this if you usually develop a single roll or a pair. It has the lowest rotary coverage minimum of the three. It’s also the first model to consider if you mainly process by hand and want the lowest full-tank fill.

2 reels max. · 280 mL rotary minimum

3 rolls · Regular batches

2530

Pick this if three rolls are your typical batch. You can run all three together without stepping up to the 2550’s higher rotary coverage minimum.

3 reels max. · 400 mL rotary minimum

4–5 rolls · Larger batches

2550

Pick this if you often have four or five rolls ready for the same process and want to run them together. Check your processor’s clearance and loaded-tank capacity before choosing it.

5 reels max. · 650 mL rotary minimum

Shoot 120 or 4×5? Check how many of your actual format-specific reels or holders fit. Do not use the 35mm roll counts to size a 120 or 4×5 batch.

Processing by hand? The sealing plug is included. Compare full-tank fill volumes before choosing; they’re higher than the rotary minimums.

Using a rotary processor? Check the drive connection, clearance, and loaded-tank limits. The optional base magnet is only for a compatible magnetic drive.

Compare capacities and prices

Prices and rotary capacities for EDL-DT tank models
Model 2502 reels
at 35mm
Rotary coverage
minimum
Price
(USD)
2520 2 280 mL $100
2530 3 400 mL $119
2550 5 650 mL $139

Coverage is not chemistry capacity. The volumes above are the physical minimums to wet the film during rotation. Use at least the greater of the tank’s minimum and the chemistry maker’s required working volume for your film load. Stay within the chemistry’s rated film capacity.

02 / Product photos

The three tanks, up close.

Compare the 2520, 2530, and 2550, then see how the cog, locking ring, and optional magnet fit. Open any photo for a larger view.

EDL-DT 2520 cog-lid tank with its parts laid out on a white background
2520Small-batch model, shown with the center column and spacer.
EDL-DT 2530 cog-lid tank with parts beside it
2530Mid-size model with the cog lid and red locking ring.
Tall EDL-DT 2550 cog-lid tank with parts beside it
2550Largest of the three models, shown beside its center column.
Close-up of the toothed drive opening at the top of the EDL-DT cog lid
Gear-drive connectionThe cog at the top of the lid engages a compatible JOBO Lift.
Hands holding the tank lid and a handle at the red locking ring
Locking ring in useThe red ring secures the lid to the tank body.
Close-up of the optional magnet mounted on the underside of an EDL-DT tank
Magnet fitted to the baseShown installed for magnetic drive. The magnet is an optional add-on (+$18).
EDL-DT cog-lid tank beside film rolls and a stack of processing reels
Tank and reels for scaleFilm and reels shown for reference; not included.
03 / Construction

Thick walls. A threaded lid.

The thick-wall PVC body helps slow heat loss. The lid screws onto the tank body rather than pressing on.

Open EDL-DT tank with the threaded underside of the lid visible
The tank body and the underside of the threaded lid.
04 / Heat retention

Less heat loss during development.

Once prewarmed, the thick-wall PVC tank helps slow heat loss. That gives you more room to work in a cool darkroom, where a cold tank can pull heat out of your developer.

Example: a C‑41 run in a cool room

Bring your developer to the temperature specified by your kit and prewarm the tank before pouring. The thick walls help the tank cool more slowly once you start the developing step. Keep using your water bath and thermometer to check that the developer stays in range.

6.2°C warmer after 30 minutes in our workshop test: the EDL-DT 2550 reached 36.2°C; an unnamed reference 2550 reached 30.0°C. Both started with the same tank temperature and equal volumes of 45°C water in 5°C air.

This was a stationary water test. It did not measure chemistry temperature in a running processor or film results.

Stationary water cooling chart: 45°C at start; at 30 minutes EDL-DT 2550 36.2°C, reference 2550 30.0°C. Ambient 5°C.
05 / Film samples

Developed in an EDL-DT tank.

Browse 15 scans developed in EDL-DT tanks: 2 Kodak 2444 scans in C-41, 9 Kodak Ektar scans in C-41, and 4 Kodak Ektar scans in C-41R.

Exposure, chemistry, and scanning all affect the finished image. These are examples, not a controlled comparison.

06 / Compatibility

Two ways to drive the tank.

Every model comes with a JOBO-spec cog lid and a sealing plug for hand processing. Add the optional base magnet for $18 when choosing your tank.

EDL-DT tank shown mounted horizontally on a rotary processor

Gear drive · Cog lid

The cog lid engages a compatible JOBO Lift. Processor shown for setup reference; not included.

Round Elevanfilm EDL-DT tank-base magnet for magnetic drive

Magnetic drive · Tank-base magnet

Fit the optional magnet to the base of the tank for use with a compatible magnetic-drive processor. Select Include base magnet (+$18) with any tank size.

07 / User guide

How to use your EDL-DT tank.

Printable A5 guide (PDF) ↗

A rotary workflow for the 2520, 2530, and 2550. For hand processing with the included sealing plug, see the full-tank fill references.

  1. Get the tank, reels, and processor ready

    Start with a dry tank and dry reels. Damp reels make film harder to load and can affect processing. Warm air used for drying must not exceed 45°C (113°F). Bring the processor’s water bath to your process temperature.

  2. Load the film and lock the lid

    In a changing bag or darkroom, load the film onto the reels. Slide the reels onto the center column so they grip and do not slip as it turns. Lower the assembly into the tank and seat the lid. Feel around the rim to check that the lid sits evenly.

    Fit the locking ring. Press down on the lid with one hand as you turn the ring clockwise. The lid should sit flush without wobbling or lifting out. If space is tight in the changing bag, finish snugging the ring with the lid handle in room light only after the tank is securely closed and light-tight.

  3. Prewarm the tank

    Mount the tank on your processor and start rotation. Once the tank is turning level, let it prewarm for 10 minutes.

  4. Process the film

    Add working solutions and follow the times and temperatures specified for your process.

  5. Open and clean the tank

    After processing, use the handle if needed and turn the locking ring counterclockwise. Remove the reels, clean the tank and accessories promptly, and air-dry them at room temperature out of direct sunlight.

Hand processing with the sealing plug

Fit the included plug before agitating by hand. These full-tank fill references are for use without a displacement spacer and are not the rotary minimums.

2520
1,600 mL
2530
2,000 mL
2550
2,800 mL
08 / Before you order

Common questions.

Yes. Each cog-lid tank includes a sealing plug for hand processing. Fit the plug before agitating and use the full-tank fill references as a starting point, not the lower rotary volumes. Follow your chemistry maker’s agitation and working-volume instructions.

The JOBO-spec cog lid fits common JOBO rotary processors equipped with a matching Lift. For other processors with a compatible magnetic drive, use the optional tank-base magnet.

The thick-wall PVC body adds weight. Check your processor’s load and clearance limits first. Before buying, test it with a comparable tank filled with water to simulate the full load of the model you plan to buy. Stay within the processor’s rated load and check that the tank turns level without slipping or stalling.

Choose a JOBO 2500-series compatible reel for your format. For 35mm, the table shows capacity with 2502 reels set to 35mm. For 120 and 4×5, use a compatible reel designed for that format. Reels are not included.

Use whichever is greater: the tank’s rotary coverage minimum or the chemistry maker’s required volume for the amount of film you’re processing. Stay within the chemistry’s rated film capacity.

Not if you use a compatible JOBO Lift and the tank’s cog lid. Choose the optional +$18 base magnet if your compatible processor uses magnetic drive.

Additional information

Model

2520, 2530, 2550

Base magnet

Tank only, Include base magnet (+$18)

There are no reviews yet.

Be the first to review “Elevanfilm EDL-DT Series | Rotary Film Developing Tanks”