Description
Which tank fits your batches?
Pick for the batch you process most often, not the biggest batch you might ever run. These recommendations assume one 35mm roll per JOBO 2502 reel.
2520
Pick this if you usually develop a single roll or a pair. It has the lowest rotary coverage minimum of the three. It’s also the first model to consider if you mainly process by hand and want the lowest full-tank fill.
2 reels max. · 280 mL rotary minimum
2530
Pick this if three rolls are your typical batch. You can run all three together without stepping up to the 2550’s higher rotary coverage minimum.
3 reels max. · 400 mL rotary minimum
2550
Pick this if you often have four or five rolls ready for the same process and want to run them together. Check your processor’s clearance and loaded-tank capacity before choosing it.
5 reels max. · 650 mL rotary minimum
Shoot 120 or 4×5? Check how many of your actual format-specific reels or holders fit. Do not use the 35mm roll counts to size a 120 or 4×5 batch.
Processing by hand? The sealing plug is included. Compare full-tank fill volumes before choosing; they’re higher than the rotary minimums.
Using a rotary processor? Check the drive connection, clearance, and loaded-tank limits. The optional base magnet is only for a compatible magnetic drive.
Compare capacities and prices
| Model | 2502 reels at 35mm |
Rotary coverage minimum |
Price (USD) |
|---|---|---|---|
| 2520 | 2 | 280 mL | $100 |
| 2530 | 3 | 400 mL | $119 |
| 2550 | 5 | 650 mL | $139 |
Coverage is not chemistry capacity. The volumes above are the physical minimums to wet the film during rotation. Use at least the greater of the tank’s minimum and the chemistry maker’s required working volume for your film load. Stay within the chemistry’s rated film capacity.
The three tanks, up close.
Compare the 2520, 2530, and 2550, then see how the cog, locking ring, and optional magnet fit. Open any photo for a larger view.







Thick walls. A threaded lid.
The thick-wall PVC body helps slow heat loss. The lid screws onto the tank body rather than pressing on.

Less heat loss during development.
Once prewarmed, the thick-wall PVC tank helps slow heat loss. That gives you more room to work in a cool darkroom, where a cold tank can pull heat out of your developer.
Bring your developer to the temperature specified by your kit and prewarm the tank before pouring. The thick walls help the tank cool more slowly once you start the developing step. Keep using your water bath and thermometer to check that the developer stays in range.
6.2°C warmer after 30 minutes in our workshop test: the EDL-DT 2550 reached 36.2°C; an unnamed reference 2550 reached 30.0°C. Both started with the same tank temperature and equal volumes of 45°C water in 5°C air.
This was a stationary water test. It did not measure chemistry temperature in a running processor or film results.

Developed in an EDL-DT tank.
Browse 15 scans developed in EDL-DT tanks: 2 Kodak 2444 scans in C-41, 9 Kodak Ektar scans in C-41, and 4 Kodak Ektar scans in C-41R.
Exposure, chemistry, and scanning all affect the finished image. These are examples, not a controlled comparison.
Two ways to drive the tank.
Every model comes with a JOBO-spec cog lid and a sealing plug for hand processing. Add the optional base magnet for $18 when choosing your tank.
Gear drive · Cog lid
The cog lid engages a compatible JOBO Lift. Processor shown for setup reference; not included.
Magnetic drive · Tank-base magnet
Fit the optional magnet to the base of the tank for use with a compatible magnetic-drive processor. Select Include base magnet (+$18) with any tank size.
How to use your EDL-DT tank.
A rotary workflow for the 2520, 2530, and 2550. For hand processing with the included sealing plug, see the full-tank fill references.
-
Get the tank, reels, and processor ready
Start with a dry tank and dry reels. Damp reels make film harder to load and can affect processing. Warm air used for drying must not exceed 45°C (113°F). Bring the processor’s water bath to your process temperature.
-
Load the film and lock the lid
In a changing bag or darkroom, load the film onto the reels. Slide the reels onto the center column so they grip and do not slip as it turns. Lower the assembly into the tank and seat the lid. Feel around the rim to check that the lid sits evenly.
Fit the locking ring. Press down on the lid with one hand as you turn the ring clockwise. The lid should sit flush without wobbling or lifting out. If space is tight in the changing bag, finish snugging the ring with the lid handle in room light only after the tank is securely closed and light-tight.
-
Prewarm the tank
Mount the tank on your processor and start rotation. Once the tank is turning level, let it prewarm for 10 minutes.
-
Process the film
Add working solutions and follow the times and temperatures specified for your process.
-
Open and clean the tank
After processing, use the handle if needed and turn the locking ring counterclockwise. Remove the reels, clean the tank and accessories promptly, and air-dry them at room temperature out of direct sunlight.
Hand processing with the sealing plug
Fit the included plug before agitating by hand. These full-tank fill references are for use without a displacement spacer and are not the rotary minimums.
- 2520
- 1,600 mL
- 2530
- 2,000 mL
- 2550
- 2,800 mL
Common questions.
Can I process film by hand?
Yes. Each cog-lid tank includes a sealing plug for hand processing. Fit the plug before agitating and use the full-tank fill references as a starting point, not the lower rotary volumes. Follow your chemistry maker’s agitation and working-volume instructions.
How do I check if my rotary processor can handle this tank?
The JOBO-spec cog lid fits common JOBO rotary processors equipped with a matching Lift. For other processors with a compatible magnetic drive, use the optional tank-base magnet.
The thick-wall PVC body adds weight. Check your processor’s load and clearance limits first. Before buying, test it with a comparable tank filled with water to simulate the full load of the model you plan to buy. Stay within the processor’s rated load and check that the tank turns level without slipping or stalling.
Which reels do I need?
Choose a JOBO 2500-series compatible reel for your format. For 35mm, the table shows capacity with 2502 reels set to 35mm. For 120 and 4×5, use a compatible reel designed for that format. Reels are not included.
How much working solution should I mix?
Use whichever is greater: the tank’s rotary coverage minimum or the chemistry maker’s required volume for the amount of film you’re processing. Stay within the chemistry’s rated film capacity.
Do I need the base magnet?
Not if you use a compatible JOBO Lift and the tank’s cog lid. Choose the optional +$18 base magnet if your compatible processor uses magnetic drive.




























There are no reviews yet.